IUT Repository Home
→
Mechanical and Production Engineering (MPE)
→
Thesis
→
Graduate
→
Browsing Graduate by Title

Browsing Graduate by Title

Now showing items 1-20 of 27

3D CFD based optimized muffler design, construction and prototype validation of motorcycle

Anwar, Ahmad Syed (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2016-11-15)

In order to minimize the sound transmission due to exhaust gases, the most common and important part of the engine system is muffler. A backpressure on engine is always produce due to the use of the exhaust muffler. This ...
Analysis of Mechanical Properties of Jute and Carbon Fiber Reinforced Epoxy Hybrid Composite

Sujon, Md Abu Shaid (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-03-30)
The augmentation of film cooling effectiveness of gas turbine (GT) blades by incorporating novel techniques

Awais, Muhammad (Department of Mechanical and Production Engineering Islamic University of Technology (IUT), Board Bazar,Gazipur-1704, Bangladesh., 2020-09-21)

Modern gas turbine engines operate at significantly high temperatures to improve thermal efficiency and power output to a greater extent. The enhancement in rotor inlet temperature (RIT) increases the heat transfer rate ...
Computational investigation of pulsatile blood flow in the models of arterial stenosis and aneurysm

Miah, Md. Abdul Karim (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2018-03-30)

A numerical analysis based on a finite volume approach is employed for a 2-D axisymmetric, incompressible, laminar flow of mean Reynolds number of 578 so as to simulate and compare the pulsatile blood flow in the models ...
Detection of Cracks in a Cantilever Metal Plate Using Vibrational Techniques

Shuvo, Sharif Rezwan (Department of Mechanical and Production Engineering, 2020-09-30)

The main objective of this research is to detect crack at different positions of the thin metal cantilever plate based on the natural frequency. Most of the researchers have investigated on beam. Few researchers have ...
Development and Evaluation of a Green Composite Materials from Natural Fibers

Bhuiyan, Md.Shah Alam (Department of Electrical and Electronic Engineering, Islamic University of Technology,Board Bazar, Gazipur, Bangladesh, 2019-11-15)

In the area of technological advancement, environmental awareness are always drawing the attention of the scientists for eco-friendly and recyclable products. Different kinds of composite materials are available in the ...
Effect of Ball Burnishing Parameters on the Surface Roughness by a Burnishing Tool with Magnetic Ball Holding Device

Hasan, Muhammad Khaled Aminul (Department of Mechanical and Production Engineering (MPE), 2017-11-15)

In this study four burnishing parameters were selected for optimizing the burnishing process using Taguchi method. The examined burnishing parameters include: (1) Burnishing speed, (2) Force and (3) Feed rate and (4) Ball ...
Improvement of Operational Quality of a Labeling and Packaging Industry by Implementing Lean Manufacturing Process

Rizvan, Ratul (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2018-11-15)
Improvement of machinability of steel during turning operation by magnetic cutting

Mahmood, Mohammad Nauzef (Department of Electrical and Electronic Engineering, Islamic University of Technology, 2012-11-15)

This study presents the results of an investigation of machinability improvement in turning of mild steel (0.25% C) by magnetic cutting. Turning experiments were done by using a precision lathe both without application ...
Investigation and Optimization of the Effects of Application of Ultrasonic Sound Frequencies during Turning Operation of Steel on Machinability Responses

Chowdhury, Mohammad Shariful Islam (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2014-11-15)

Turning is one of the most common and popular process in industry for manufacturing metallic products. The two single most important output parameters that define the product quality are surface roughness and tool wear. ...
Investigation of the NOx and SOx Emissions from Large-Scale Coal-Based Power Plants

Firoz, Mahmudul (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2024-06-12)

Coal-fired power plants are a pivotal source of energy in Bangladesh, a country with abundant coal reserves. Yet, the environmental and health risks linked to the greenhouse gas emissions from these plants are significant ...
Life Cycle Assessment of Renewable Energy Technologies of Bangladesh

Baky, Md. Abdullah Hil (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2017-08-30)

As the benefit of the renewable energy systems getting more and more clear to people, these are being introduced in small scale and large scale in both developed and developing countries. Renewable energy systems show a ...
Numerical and Experimental Investigation of Shock wave Propagation in the Open Atmosphere

Ehsan, Mohammad Monjurul (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2012-11-15)

Shock wave propagation in the open atmosphere has been investigated both numerically and experimentally. Three-dimensional numerical code has been used to solve the Euler equations for the upstream and downstream parameters ...
A Numerical Investigation of Local Scour Around Different Shape of Bridge Piers and Its Reduction

Hasan, Rumana (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2022-06-30)

Around the world, local scour is one of the leading causes of bridge collapses and other hydraulic structure failures. The study demonstrates the scour depth and fluid dynamics of different shaped bridge piers, including ...
Numerical Study of Emission Control of Urban and Rural Kitchens for Healthy Environment

Rahman, Md. Hamidur (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2016-03-28)

Lack of proper ventilation of exhaust fumes from gas and biomass fired stoves in both urban and rural residential kitchens are a major health concern for majority populations. It could even cause destruction of property, ...
Optimization of Maintenance Management Framework in LPG Cylinder Manufacturing

Sarker, Md Shamsuzzoha (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2022-06-30)

Maintenance can be defined as actions necessary for retaining or restoring a piece of equipment, machine or system to the specified operating conditions to achieve its maximum useful life. Maintenance ensures that ...
Optimization of the Critical Production Process in a Textile Factory using AHP

Islam, Md. Tajul (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-12-24)

The process of converting raw materials, components, or parts into finished goods that meet customer’s expectations or specifications is called the production process. Manufacturing commonly uses a man-machine set up with ...
Parametric Analysis of Thermal performance of Earth-To-Air-Tunnel-Heat Exchanger (EATHE)

Rana, Masud (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2022-07-30)

The Earth-to-Air-Tunnel-Heat Exchanger (EATHE) is one of several ambient air conditioning systems with minimum cost. Several factors and conditions will enhance the performance of the installed EATHE in room air conditioning ...
Performance analysis of a fully automated green Effluent Treatment Plant (ETP)

Aishan, AbdulazizMoqbelMoqbel (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2019-11-15)

The major goal of this work is to focus the pollution scenario of our environment due to textile effluent from textile industries and how we can develop and upgrade our system so that the pollution level can be minimized. ...
Prediction and Optimization of Quality of Drilled Holes During Magnetic Drilling Operation of Glass Fiber Reinforced Polymer Composite

Yusuf, Suleiman Mohammed (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)

This study presents the results of an investigation of the use of Box Behnken design approach to plan the experiments for drilling GFRP composite under different magnetic conditions with an overall objective of optimizing ...

Now showing items 1-20 of 27

Search IUT Repository

Advanced Search

Browse

All of IUT Repository
This Community
- By Issue Date
- Authors
- Titles
- Subjects

Browsing Graduate by Title

Browsing Graduate by Title

Search IUT Repository

Browse

All of IUT Repository

This Community

My Account