2017: Recent submissions

  • EAHE-Solar Chimney Coupled Passive Cooling System and the Simulation 
    Alam, Chowdhury Sadid; Dhrubo, Tm Abir Ahsan (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    In the 21st century the talk of the time has been proper use of renewable energy sources due to the continuous depletion of non-renewable energy sources and global warming as a result of combustion of fossil fuels. The ...
  • Investigation of Surface Roughness During Hot Air Streaming Turning Process of Different Materials and Optimization of Parameters Using Particle Swarm Optimization 
    Mahmud, Md. Firoz; Islam, Md. Minhazul (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    Different types of coolants are widely used in different metal cutting processes to improve the machining responses. But the suitability of using the correct cutting fluid is very important considering the concept of green ...
  • Designing and Construction of Solar Tracker 
    Abdullah; Muhammad, Jebreel (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    The crucial purpose of our systematic experimental technique is to concentrate the solar radiation on the solar panel i.e. to construct a solar tracker system which will be capable of converting maximum sun light to ...
  • Minimization of Shrinkage Defect in Crankshaft Casting 
    Abubakar, Zayyad; Ullah, Najeeb (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    In our present study, we mainly focused on the reduction of the casting and moulding defects that mainly occurs during metallurgical process and we are able to depict some of those severe problems that might hamper the ...
  • Design of a Net Zero Energy Building in Bangladesh using Building Energy Optimization Simulation Tool 
    Aziz, Waleed; Rashik, Rafsan Ahmed (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    A Net Zero Energy Building (NZEB) is a residential or commercial building with greatly reduced energy consumption by efficiency means, such that the remaining energy load can be supplied with Renewable Energy (RE) technologies. ...
  • Design & Fabrication of Vortex Tube for Industrial Cooling 
    Abeer, Arik Inkiyad; Uddin, Md. Misbah; Khan, Muhammad Hamza; Rahma, Yousif; Alkasim, Hassan; Hayat, Khurram (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    A cooling system is very important for both man and machine. In general vapor compression refrigeration system and vapor absorption refrigeration system are used for refrigeration purpose. Vortex tube cooling system is a ...
  • Effect of holes placed on the perforated finned heat exchanger at different angles on the Nusselt and Reynolds numbers 
    Saad, Muhammad (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    In this research, 6mm diameter holes were opened on each circular fin on a heating tube in order to increase convective heat transfer. This is different from the other studies in the literature. These holes were placed ...
  • 3d Numerical Investigation of Flow and Heat Transfer Characteristics in Smooth Wavy Fin and Elliptical Tube Heat Exchangers Using ARW Vortex Generator 
    Sabbir, Shah Mohammad; Chowdhury, Sadat Hasan (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    3D computational analysis was performed to investigate heat transfer and pressure drop characteristics of flow in SWFET (Smooth Wavy Fin-and-Elliptical Tube) heat exchanger with VGs (vortex generators). The numerical model ...

Search IUT Repository


Advanced Search

Browse

My Account