IUT Repository Home
→
Mechanical and Production Engineering (MPE)
→
Browsing Mechanical and Production Engineering (MPE) by Title

Browsing Mechanical and Production Engineering (MPE) by Title

Now showing items 1-20 of 311

3D CFD based optimization technique for muffler design of a motorcycle

Shadman, Sakib; Abir, Oneeruddho Hussain (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)

In order to minimize the sound transmission due to exhaust gases, the most common and important part of the engine system is muffler. A back pressure on engine is always produced due to the use of the exhaust muffler. This ...
3D CFD based optimized muffler design, construction and prototype validation of motorcycle

Anwar, Ahmad Syed (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2016-11-15)

In order to minimize the sound transmission due to exhaust gases, the most common and important part of the engine system is muffler. A backpressure on engine is always produce due to the use of the exhaust muffler. This ...
3d Numerical Analysis of The Effect of Various Geometric Parameters of Eathes Under Steady Operating Conditions

Hero, Md. Kabbir Hossain; Moin, Md. Emran Hossain (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2018-11-15)

Space heating and cooling is a comfort requirement which results in a significant amount of energy consumption. EATHE (Earth Air Thermal Heat Exchanger) is one of the passive ways of space heating and cooling that can ...
3d Numerical Investigation of Flow and Heat Transfer Characteristics in Smooth Wavy Fin and Elliptical Tube Heat Exchangers Using ARW Vortex Generator

Sabbir, Shah Mohammad; Chowdhury, Sadat Hasan (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)

3D computational analysis was performed to investigate heat transfer and pressure drop characteristics of flow in SWFET (Smooth Wavy Fin-and-Elliptical Tube) heat exchanger with VGs (vortex generators). The numerical model ...
Accessible Design and Fabrication of Wheelchair Ramp for Public Bus Transportation and Design Study Based on SolidWorks Simulation

Ahmed, Syed Tasnim; Islam, Sakib Ul (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)

There are an estimated 5.6% people in Bangladesh who have a disability of one kind or another and about 28% of disabled people have physical disabilities. Movement accessibility is an important enabler of strategies to ...
Analysis & Comparative Study on Different Cooling Systems of Motorbike Engines and Implementation of Thermoelectric Generator (TEG) on the Exhaust System

Himel, Ashif Ahmmed; Hussain, Md Riasat; Sadi, Ahnaf (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2021-03-30)

For a smooth running of the engine as well as to maintain an optimum performance, the engine needs to be cooled down. With the number of motorbikes increasing day by day in Bangladesh, finding an optimum cooling system for ...
Analysis and Optimazation on Thermal Efficiency of Automobile Engines

Mahfuz, Araf; Ahmed, Ashik (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2018-11-15)

The thermodynamic limitation for the maximum efficiencies of internal combustion engines is an important consideration for the design and development of future engines. Knowing these limits helps direct resources to those ...
Analysis of Bimorph Piezoelectric Energy Harvester Attached With a Cantilever Beam Under Excitation

Alam, Syed Sifat; Rhythm, Ahnaf Sharaf (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2021-03-30)

In this thesis work a cantilever structure based bimorph piezoelectric energy harvester have been designed and analyzed using lead zirconium titanate (PZT 5A) as piezoelectric material and steel as the elastic substrate ...
Analysis of different metamaterials based on low frequency sound transmission loss using comsol multiphysics

Rahman, S. M. Mustafizur; Zakir, Junayed Bin (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), 2022-05-30)

In this day and age noise reduction is an increasingly relevant and rapidly progressing sector of technology. It is necessary due to the numerous psychological benefits of a relatively quiet atmosphere. In this paper, we ...
Analysis of different Supercritical CO2 Brayton Cycles Integrated with Transcritical CO2 Cycle and Organic Rankine Cycle

Sadat, Khandekar Nazmus (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2023-06-30)

For concentrating solar power (CSP) applications, supercritical CO2 (S-CO2) has the potential to provide greater cycle efficiency than superheated or supercritical steam cycles. The transcritical CO2 cycle (TCO2 cycle) ...
Analysis of Different types of cracks on Beams and Plates

Shajid, Soad; Sajol, Sazzadul Islam (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2021-03-30)

Beam and plates in existence of crack is vulnerable to failure reckoning on the different mode of vibration. The natural frequency of the beams and plates and the superposition of periodic force acting on beams and plates ...
Analysis of Mechanical Properties of Jute and Carbon Fiber Reinforced Epoxy Hybrid Composite

Sujon, Md Abu Shaid (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-03-30)
Analysis of muscles and gripping activities of human hand during drilling operation

Khan, Taimur Hassan; Alaqad, Mohammed H (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2014-11-15)

Drilling is the most common machining process. One estimate is that 75% of all material removed comes drilling operations. Drilling involves the creation of holes that are right circular cylinders. This is accomplished ...
Analysis of Wave Impact on Offshore Structure & Modeling a Physical Wave Creating Device

Mannan, Fahad; Imtiaz-Ur-Rahman, Md.; Hossain, Md. Alamin (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)

Structures in offshore seabed area is quite common affair.Offshore monopile foundation is one of the most commonly used foundation structures.The Sangu Gas field in Sangu river is an example in our country.These offshore ...
Application of Modern Supply Chain Management Tools to Power Plants of Bangladesh: A Case Study

Mahmud, Asif; Hossain, Md. Moinul (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)

Power generation sector of a country plays a pivotal role in her overall development and progress. In modern world, as days goes by people are getting depended on technology even more. Bangladesh is the ninth most populous ...
Assessment and Characterization of Potential Locations for Wind Energy Harvest in Bangladesh

Tasnim, Maliha; Rifa, Tasnia Islam (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2023-05-30)

Wind, solar, hydro, and geothermal renewable energy sources are becoming more and more important for tackling the energy issue and reducing climate change. Wind energy is regarded as one of nature's cleanest, safest, ...
Assessment of Biogas Potential at IUT from Cafeteria Waste

Sayed, Abu; Islam, Khirul; Ali, Md. Hasan; Islam, Md. Shafiul (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur-1704, Bangladesh, 2021-03-30)

Biogas is a source of clean energy and one kind of renewable energy resource which has highly influence in waste management. Anaerobic digestion is used in formation of biogas from different organic materials and it makes ...
Assessment of Quality Management System and Intervention of Lean Six Sigma Tools in a Ready Made Garments (RMG) Factory

Nafiz, Afsan; Aziz, Md. Abdul (Department of Mechanical and Production Engineering, 2021-03-30)

Quality Management Systems have become an integral part of modern manufacturing processes. Lean Manufacturing approach, Six Sigma Methodologies and the various tools of Lean Six Sigma approaches are increasingly being ...
The augmentation of film cooling effectiveness of gas turbine (GT) blades by incorporating novel techniques

Awais, Muhammad (Department of Mechanical and Production Engineering Islamic University of Technology (IUT), Board Bazar,Gazipur-1704, Bangladesh., 2020-09-21)

Modern gas turbine engines operate at significantly high temperatures to improve thermal efficiency and power output to a greater extent. The enhancement in rotor inlet temperature (RIT) increases the heat transfer rate ...
Automated Number Plate Recognition

Ridoy, Md Abdur Rahman (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2018-11-15)

Now showing items 1-20 of 311

Search IUT Repository

Advanced Search

Browse

All of IUT Repository
This Community
- By Issue Date
- Authors
- Titles
- Subjects

Browsing Mechanical and Production Engineering (MPE) by Title

Browsing Mechanical and Production Engineering (MPE) by Title

Search IUT Repository

Browse

All of IUT Repository

This Community

My Account