Thesis: Recent submissions

  • Improvement of high speed rail pantograph control system using PID controller 
    Alnawafleh, Anas; Almoghrabi, Abdallah; Anda, Mahmud (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
  • Comparative study of I.C. engine performance using different fuels 
    Shuvo, Mohammad Reyad Arefin; Noor-e- Mostofa, Abdullah (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    Comparative study of I.C. engine using different fuels is the test of engine performances for different properties of engine as well as comparing these properties using different fuels. The processes involved measuring ...
  • Study of supply chain management of an industry 
    Fahim, Mirza Abu (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    Supply chain management (SCM) is a factory management technique that aims at maximum profit from a business by ensuring visibility in the supply chain. SCM is a dynamic management tool, which is a combination of many ...
  • Effect of ultrasonic sound wave on machinability parameters during turning operation of mild steel 
    Russel, Md. Omar Faruque (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    This project aims to investigate the effects of ultrasonic sound signal on the machinability control of mild steel during turning operation. The machinability responses include tool wear, surface roughness, temperature, ...
  • Design, Construction and study of performance of a flat-plate solar heater for winter air conditioning of a small residential building in Bangladesh 
    Haq, Mahmud Arefin; Rashid, Adib bin (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    Rising costs of conventional fuels, increasing energy demand, concerns over climate change and pollutants resulted from burning fossil fuels have increased the interest in various renewable energy technologies. The ...
  • Design, construction & testing of a ½ tr r-12 bare-tube forced convection evaporator for cooling air 
    Haque, Md. Shafiul; Shah, Yousaf (Department of Mechanical and Production Engineering (MPE), 2013-11-15)
    The title of my project is DESIGN, CONSTRUCTION & TESTING OF A ½ TR R-12 BARE-TUBE FORCED CONVECTION EVAPORATOR FOR COOLING AIR. The goal of this presentation is to design and construct a bare tube forced convection ...
  • Investigation of surface parameters using green coolant in drilling process 
    Akram, Rana Muhammad Hassnain (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    Computer Numerical Control (CNC) is specialized and versatile form of soft Automation in which the functions and motions of a machine tool are controlled by means of a prepared program containing coded alphanumeric data. ...
  • RFID based car parking system in IUT 
    Islam, Saiful; Hasan, Muhit (Department of Electrical and Electronic Engineering, Islamic University of Technology (IUT), Board Bazar, Gazipur-1704, Bangladesh, 2013-11-15)
    The goal of our project is to develop a RFID based car parking system in IUT. For achieving this goal we needed to design a electrical circuit integrating RFID reader & tag with a arduino board. At the end of the semester ...
  • Computational investigation of pulsatile blood flow in the models of arterial stenosis and aneurysm 
    Miah, Md. Abdul Karim (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2018-03-30)
    A numerical analysis based on a finite volume approach is employed for a 2-D axisymmetric, incompressible, laminar flow of mean Reynolds number of 578 so as to simulate and compare the pulsatile blood flow in the models ...
  • Life Cycle Assessment of Renewable Energy Technologies of Bangladesh 
    Baky, Md. Abdullah Hil (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2017-08-30)
    As the benefit of the renewable energy systems getting more and more clear to people, these are being introduced in small scale and large scale in both developed and developing countries. Renewable energy systems show a ...
  • Analysis of Wave Impact on Offshore Structure & Modeling a Physical Wave Creating Device 
    Mannan, Fahad; Imtiaz-Ur-Rahman, Md.; Hossain, Md. Alamin (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
    Structures in offshore seabed area is quite common affair.Offshore monopile foundation is one of the most commonly used foundation structures.The Sangu Gas field in Sangu river is an example in our country.These offshore ...
  • Study of a Convective Heat Transfer for Laminar and Turbulent Flow of Nano-fluid through a Circular Pipe 
    Mehmood, Aqib; Ismail, Motapon Njikam; Ndiaye, Babacar (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
  • 3D CFD based optimization technique for muffler design of a motorcycle 
    Shadman, Sakib; Abir, Oneeruddho Hussain (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
    In order to minimize the sound transmission due to exhaust gases, the most common and important part of the engine system is muffler. A back pressure on engine is always produced due to the use of the exhaust muffler. This ...
  • Study of Effect of Different Burnishing Conditions on Surface Roughness for a Flexible Burnishing Tool 
    Hossain, Tapos; Tuser, Md. Towkir Ahmed; Ovy, S.M. Al Islam (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
    Burnishing is a very simple and effective method for improvement in surface finish and can be carried out using existing machines, such as lathe. Quality of Surface is an important factor to decide the performance of a ...
  • Stress and Vibration Analysis of a MDOF Excavator Bucket 
    Islam, Md Shahriar (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
    Multi degrees of freedom (MDOF) excavator is a very popular machine in today’s mining industry and are also popularly used in roads and building constructions or demolition and for material handling. All these uses involve ...
  • Prediction and Optimization of Quality of Drilled Holes During Magnetic Drilling Operation of Glass Fiber Reinforced Polymer Composite 
    Yusuf, Suleiman Mohammed (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2015-11-15)
    This study presents the results of an investigation of the use of Box Behnken design approach to plan the experiments for drilling GFRP composite under different magnetic conditions with an overall objective of optimizing ...
  • Detection of Cracks in a Cantilever Metal Plate Using Vibrational Techniques 
    Shuvo, Sharif Rezwan (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-11-15)
    The main objective of this research is to detect crack at different positions of the thin metal cantilever plate based on the natural frequency. Most of the researchers have investigated on beam. Few researchers have ...
  • Analysis of Mechanical Properties of Jute and Carbon Fiber Reinforced Epoxy Hybrid Composite 
    Sujon, Md Abu Shaid (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-03-30)
  • Optimization of the Critical Production Process in a Textile Factory using AHP 
    Islam, Md. Tajul (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2020-12-24)
    The process of converting raw materials, components, or parts into finished goods that meet customer’s expectations or specifications is called the production process. Manufacturing commonly uses a man-machine set up with ...
  • Development of an Innovative Fireball Fire Extinguishing System 
    Elahi, Ashique E; Rahman, Minhajur (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2019-11-15)
    Industries are facing a lot of fire based accidents these days. As a result, massive losses of lives as well as money are suffered by the owners. The conventional fire extinguishing systems are found to be not enough to ...

Search IUT Repository


Advanced Search

Browse

My Account