Browsing Undergraduate by Title

Browsing Undergraduate by Title

Sort by: Order: Results:

  • Development of Carboxymethyl Cellulose (CMC) Based Electro Active Polymer Nano Composite & Its Potential Application As Solid State Dye Sensitized Solar Cell 
    Mahbub, Md. Zakaria (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2012-11-15)
    Organic solar cell research has developed during the past 30 years, but especially in the last decade it has attracted scientific and economic interest triggered by a rapid increase in power conversion efficiencies. This ...
  • Development of IOT Based Smart Irrigation System 
    Salah, Awad; Oumarou, Almouzzammil; Ismaila, Mouhammad Hamza; Amadou, Oumarou (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2023-05-30)
    This project presents an IOT based smart irrigation system in order to optimize watering schedules for plants and lawns. The system uses an Arduino Uno microcontroller in conjunction with IoT(Internet of Things) sensors ...
  • Development of The Capsule Orientation Mechanism of an Automatic Capsule Filling Machine 
    Khan, Towhid Alam (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2012-11-15)
    In the automatic Capsule filling machine Vacuum is used to separate the cap and body of a capsule before inserting the formulation into the body part of the capsule. This Vacuum pump consumes a very high amount of power. ...
  • EAHE-Solar Chimney Coupled Passive Cooling System and the Simulation 
    Alam, Chowdhury Sadid; Dhrubo, Tm Abir Ahsan (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    In the 21st century the talk of the time has been proper use of renewable energy sources due to the continuous depletion of non-renewable energy sources and global warming as a result of combustion of fossil fuels. The ...
  • Effect of holes placed on the perforated finned heat exchanger at different angles on the Nusselt and Reynolds numbers 
    Saad, Muhammad (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2017-11-15)
    In this research, 6mm diameter holes were opened on each circular fin on a heating tube in order to increase convective heat transfer. This is different from the other studies in the literature. These holes were placed ...
  • Effect of Mechanical Vibrations In Sand Casting of Aluminium Alloy Using Organic Binders 
    Mahmud, Safayet; Rownak, Ragib (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2022-05-30)
    This paper represents a systematic finite element analysis to evaluate the various mechanical vibration impacts on sand mold casting during aluminum alloy cooling. In general, the mold materials govern the molten metal ...
  • Effect of Point and Line Defects on the Mechanical Behavior of Single Layer MoTe2 
    Aziz, Md. Jobayer (Department of Mechanical and Production Engineering(MPE), Islamic University of Technology(IUT), Board Bazar, Gazipur-1704, Bangladesh, 2023-05-30)
    Following the groundbreaking discovery of graphene, the scientific community has witnessed a surge of interest in two-dimensional (2D) materials during recent times, remarkable capabilities and versatility for technological ...
  • Effect of Rake Angle & Relief Angle in Chip Formation During Turning Operation 
    Ahmed, Tanvir; Anik, Eftekharul Hoque; Rythm, Fahim Ajmal (2018-11-15)
    The simulation of various machining processes is a matter of interest in active research for over two decades. This study develops a combined simulation based and experimental approach to find the effect of rake Angle & ...
  • Effect of rake angle and cutting speed in chip morphology and prediction of tip temperature and cutting forces with FEA software 
    Khalid, Saifullah; Tanzil, Sifat Ullah (IUT, MCE, 2016-11-20)
    To minimize experimental time and expensive experimental test, researchers always refer FEA as most effective system. In this paper, we tried to show the effect of rake angle, cutting speed in chip morphology for different ...
  • Effect of Scouring Around Bridge Piers 
    Enam, Samin (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2012-11-15)
    A series of relatively recent bridge failures due to pier scour, as reported in literature, has rekindled interest in furthering our understanding of the scour process and for developing improved ways of protecting bridges ...
  • Effect of tool geometry ob chip morphology and cutting parameters in turning process by FEM analysis 
    Meem, Rahnum Tahia (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2021-03-30)
  • Effect of Tool Geometry on Chip Morphology and Cutting Parameters in Turning Process by FEM Analysis 
    Meem, Rahnum Tahia (Department of Mechanical and Production Engineering, 2021-03-30)
    The purpose of this study is to analyze various parameters like temperature, pressure, max shear stress etc while keeping two parameters constant
  • Effect of ultrasonic sound wave on machinability parameters during turning operation of mild steel 
    Russel, Md. Omar Faruque (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2013-11-15)
    This project aims to investigate the effects of ultrasonic sound signal on the machinability control of mild steel during turning operation. The machinability responses include tool wear, surface roughness, temperature, ...
  • Effect of Variation of Aerodynamic Brake Plate Orientation and Multiple Brake Geometries on Incident Drag of Hyperloop Pod 
    Khan, Shahnoor Shamim; Mahmud, Shadman; Adnan, Adib (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2019-11-15)
    The idea for the Hyperloop has received significant attention, with commentators and analysts expecting it to become a revolutionary and potentially the fastest mode of land transportation on the planet. Various companies ...
  • Effects of magnetism on the roughness of drilled holes of a glass fiber reinforced polymer composite material 
    Shahriar, Md. Ragib; Azam, Md. Firdous (IUT, MCE, 2016-11-20)
    Have superior properties of the glass fiber reinforced polymer (GFRP) composite materials, the use of it is being accelerated recently. That is why the machining of these GFRP materials is a great concern for engineers. ...
  • Effects on Natural frequency of Simply Supported Square Plate due to concentrated masses and Circular Cutout 
    Ahshan, Kh. Nazmul; Arnob, Nazmul Hossain (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2014-11-15)
    In any operation performed by machine on any structure vibration may occur. This vibration can be devastating when the frequency matches with the natural frequency of that structure. Due to resonance the structure can be ...
  • EGR cooler design 
    Abdilahi, Osman; Ali, Saqib; Waseem, Muhammad; Kaihan, Mohammad Kazem (Department of Mechanical and Production Engineering, Islamic University of Technology, Gazipur, Bangladesh, 2019-11-15)
    During the EGR cooler performance is a key issue that a ects the function of EGR system as an anti-pollutant device. There is a signi cant concern to guarantee function of these devices during useful life of vehicle. ...
  • Electro-Magnetic Suspesion System for Vehicles 
    Rahman, Kazi Moshiur (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2012-11-15)
    A conceptual model of electro-magnetic suspension system is presented. The goal is to provide better performance and smooth operation than the conventional one. Two electro-magnets are used to use the repulsive force to ...
  • An end-use energy consumption on Bangladeshi textile industry 
    Salman, Asif; Mehadi, Md. Riyad (Department of Mechanical and Production Engineering (MPE),Islamic University of Technology(IUT), Board Bazar, Gazipur, Bangladesh, 2014-11-15)
    In industrial sector the overall demand of electricity is increasing by about 5% per year in industrial sector. An energy consumption audit was conducted in Kojima Lyric Garments, Gazipur to determine the total electrical ...
  • Energetic Analysis and Design of Waste Heat Recovery for Amran Cement Industry 
    Mahyoub, Md. Khaled Md. Abdulqader; Mojaly, Hassan Mohammed Ahmed; Abushibh, Dhiaa Yahya Ali (Department of Mechanical and Production Engineering, Islamic University of Technology, Board Bazar, Gazipur, Bangladesh, 2018-11-15)

Search IUT Repository


Advanced Search

Browse

My Account